ccg-d1ex-captive-component-cable-gland-0519
ccg-d1ex-captive-component-cable-gland-0519

Product overview

CCG D1EX Captive Component Cable Gland (0519)

CCG D1EX Captive Component Cable Gland (0519) is a Hazardous Area Glanding Device for Steel Wire Armoured Cable. Suitable for indoors, outdoors, Group II, III, Zone 1, 2, 20, 21 and 22 hazardous areas.

CCG Part Numbers: 051900-16, 051900, 0519-0, 051901, 051922, 051902, 051933, 051903, 051944, 051904, 051955, 051905, 051966, 051906, 051977, 051907, 051908, 051999, 051909, 051810, 051911, 051912, 051913

Features & Benefits

  • For indoors, outdoors, Group II, III, Zone 1, 2, 20, 21 and 22 hazardous areas.
  • Two-piece handling, no loose parts.
  • A freely rotating captive cone and inspectible cone ring provides an armour clamp and earth bond on steel wire armour.
  • A specially formulated elastomeric seal for Built-in Safety™, seals on the inner sheath of the cable IP65/66/68.
  • Precision manufactured from high-quality brass (Marine Grade Electroless Nickel Plated™).
  • Supplied with a thread sealing gasket (parallel threads only).

CCG D1EX Technical Data

Type: D1EX
Equipment Protection Levels: Ex db IIC, Ex eb IIC, Ex nR IIC, Ex ta IIIC
Gland Material: Brass (Marine Grade Electroless Nickel Plated™)
Seal Material: Standard Thermoset Elastomer or Extreme Temperature Seals
Sealing Gasket Material: HDPE, Nylon 66 or PTFE
Cable Type: Steel Wire Armour
Armour Clamping: Rotating Captive Cone and Inspectible Cone Ring
Sealing Area: Inner Sheath
Optional Accessories: Adaptor, Reducer, Earth Tag, Locknut, Serrated Washer and Shroud

Note: The installer should ensure that the materials are suitable for the installation environment.

Installation Standards

  • IEC/BS EN
  • IECEx
  • ATEX
  • UKEX
  • INMETRO (Brazil)
  • TR CU (Russia)
  • SANS
  • Ingress Protection
  • Deluge Protection
  • Corrosion Protection
  • Marine ABS
  • DNV-GL
  • EMC Compatible

Hazardous Areas

A Hazardous Area is one in which there is potential for an explosion of gases, vapours, mists or dust or a combination of these. Such locations are petrochemical plants, offshore oil rigs, fuel filling stations, timber mills, coal mines, flour mills, paint spray booths, sewerage treatment plants, hospitals, explosive magazines and more.

Special precautions must be taken for the design, manufacture, installation and use of equipment and cable glands in such hazardous areas. Persons involved in selecting installing and maintaining electrical equipment for use in hazardous areas should be competently trained, have a full understanding of what a hazardous area is and have knowledge of the equipment protection levels and the installation standards involved.

Additional Technical Data on CCG D1EX Captive Component Cable Gland (0519) Part Numbers can be found on the table below. For Conforming Standards & Certificates as well as Fitting Instructions, please advise PDF File.

FREE Technical Advisory Service
E-Tech Components UK Ltd maintains a free technical advisory service.
Contact us for enquiries concerning this and all other products: +44 (0) 1744 762 929

Technical Data

Product Code Gland Size Ref. Metric Entry Thread (C) Metric Entry Thread (Min D) NPT Entry Thread (C) NPT Entry Thread (Min D) Cable Detail (Min A) Cable Detail (Max A) Cable Detail (Max B) Max Length (E) Armour Dia (Min F) Armour Dia (Max F) Hexagonal Detail (Max Flats) Hexagonal Detail (Max Crns) Installation Torque Value (Nm)
051900-16 00-16ss M16x1.5 15 - - 3 8.5 13.5 53 0.20 0.90 24 27 21
051900 00-20ss M20x1.5 15 ½/¾ 15 3 8.5 13.5 53 0.20 0.90 24 27 21
0519-0 0-20s M20x1.5 15 ½/¾ 15 7 12 16 53 0.20 1.25 24 27 21
051901 1-20 M20x1.5 15 ½/¾ 15 9 15 20.5 56 0.20 1.25 27 30 21
051922 2s-25s M25x1.5 15 ¾/1 15/19 11 17.5 24.5 60 0.20 1.60 35 39 30
051902 2-25 M25x1.5 15 ¾/1 15/19 14 20 26.5 60 0.20 1.60 35 39 30
051933 3s-32s M32x1.5 15 1/1¼ 19 15 22 30.5 66 0.20 2.00 42 47 42
051903 3-32 M32x1.5 15 1/1¼ 19 19 26.5 33.5 66 0.20 2.00 42 47 42
051944 4s-40s M40x1.5 15 1¼/1½ 19/21 22 31.5 39.5 78 0.30 2.00 52 59 52
051904 4-40 M40x1.5 15 1¼/1½ 19/21 26 34 42.5 78 0.30 2.00 52 59 52
051955 5s-50s M50x1.5 15 1½/2 21 29 38 47.5 87 0.40 2.50 65 73 57
051905 5-50 M50x1.5 15 1½/2 21 34 44.5 52.5 87 0.40 2.50 65 73 57
051966 6s-63s M63x1.5 15 2/2½ 21/30 38 50 60.5 110 0.40 2.50 80 90 66
051906 6-63 M63x1.5 15 2/2½ 21/30 44 56.5 65.5 110 0.40 2.50 80 90 66
051977 7s-75s M75x1.5 15 2½/3 30/32 50 62 72.5 118 0.40 3.15 96 108 72
051907 7-75 M75x1.5 15 2½/3 30/32 56 67.5 78 118 0.40 3.15 96 108 72
051908 8-80 M80x2.0 20 3 32 59 69 77.5 175 2.50 3.15 96 108 80
051999 9s-90s M90x2.0 20 3/3½ 32/33 66 75 86.5 184 3.00 3.50 111 125 89
051909 9-90 M90x2.0 20 3/3½ 32/33 74 81.5 91 184 3.00 3.50 111 125 89
051910 10-100 M100x2.0 20 3½/4 33/34 81 91 100 189 3.00 3.50 125 141 89
051911 11-115 M115x2.0 20 4 34 86 98 114 189 3.00 4.00 135 152 175
051912 12-120 M120x2.0 20 - - 95 103 118 189 3.00 4.00 140 158 175
051913 13-130 M130x2.0 20 - - 100 115 124 189 3.00 4.00 146 164 175

All dimensions except NPT are in mm. Intermediate thread sizes are available on request. NPT threads should be tightened ‘wrench tight’.

 

Find out more about our products or becoming a supplier